دانلود AC-Tek Sidewinder v7.2.2 - نرم افزار تخصصی طراحی بالابرهای صنعتی و نوار نقاله

- International Standards & Calculation Methodologies (English and Metric Units)
Conveyors are found around the globe. From small in-plant conveyors to the large overland systems, and in all regions of the world. The ability for the software to perform calculations in both standard and SI units was an obvious must. Additionally, users can quickly switch units for all input and output data with a single mouse click.   As there are several different calculation methodologies used worldwide, we have chosen to include all which we feel are the most relevant. Both the universally accepted DIN and CEMA standards are available. Other published methodologies are also available (Jonkers, Spans, etc). These methods use the specific belting rubber viscoelastic properties and other factors.

- Professional Quality Design Reports
High quality professional output files were at the top of the list when determining the most important engineering features to include in Sidewinder. A custom report editor is built into the software, as well as the ability to export reports directly to Microsoft Word documents and Adobe PDF files. Company logos and other custom information can be specified in the software. Pulleys, brakes, and other major equipment lists are generated which can be directly supplied for manufactures for quotations.

- Conveyor Geometry
One of the more difficult aspects of conveyor design is accurately inputting the conveyor profile. Sidewinder has three methods for entering this information:

   - Easy Profile – Allows a basic conveyor profile to be entered using only a few conveyor elements. All basic information is entered on a single screen and can easily be modified later. Dozens of standard conveyor configurations are available in order to minimize the input requirements for the end user. This is appropriate for most small conveyors (<1000 ft.) which have relatively simple profiles.

   - Standard Profile – Allows an unlimited number of vertical and horizontal curves to be entered. This information can be directly entered, or imported from several standard drawing packages such as AutoCAD. Each conveyor flight is treated individually, and vertical and horizontal curves are automatically subdivided at runtime to provide an accurate representation of the conveyor.

- Integrated System Design
Many conveyor systems have a wide range of operating conditions. These include variations in:
   - Material properties and/or multiple material types
   - Conveyor load variations (incline or decline sections loaded, load on and off)
   - Hot summer time temperatures, to frigid winter conditions
   - Belt mass reduction and other changes due to cover wear and environmental factors
   - Idler bearing drag and motor efficiencies
   - Other factors

- Custom Idler Types
Users can choose to use either a standard CEMA idler set, or a custom idler set. Custom idler sets allow up to six independent custom idler rolls to be used. Additionally, each roll is customizable within each idler set. This allows center rolls to have unique properties (length, bearing type, shaft size, etc) from wing or other rolls.

- Multiple Material Types & Byway Conveying
Up to five different material types may be entered for a single design. This is not only useful for analyzing worst case design conditions (for example using the lowest material density for maximum cross sectional loading), but also allows the conveyor to transport more than one material type.

- Dynamics – Starting / Stopping / Emergency Stopping
Relatively long conveyors, or conveyors with large inclines or declines should have a flexible dynamic analysis preformed on them (see dynamic analysis). However, ridged dynamic calculations are often more than adequate for short conveyors, and for preliminary estimation of the dynamic belt tensions and braking requirements.

- Belting and Belt Stresses
Sidewinder has combined a wide range of belting data from several of the leading belting manufacturers. This includes properties for both fabric and steel cord belting.

- Pulley Shaft & Bearing Sizing
Pulley diameters, shaft stresses, bearing loads, allowable turndown ratios, and other important design information is automatically calculated for each pulley. An accurate graphical representation for each pulley is displayed showing belt tensions, wrap angles, and the pulley geometry.

- Right Angle Drives with Overhung Loads
Sidewinder includes an advanced workpage allowing overhung loads to be determined for various power conditons. These loads can then be used in the normal pulley and shaft calcaution equations. Sidewinder allows the user to enter all known masses and the center of gravity (CG) of each item. However, if these items are unknown Sidewinder can also estimate them using internal libraries created from published user catalog data.